// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2711.dtsi"
#include "bcm2835-rpi.dtsi"

/ {
	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
	model = "Raspberry Pi 4 Model B";

	chosen {
		/* 8250 auxiliary UART instead of pl011 */
		stdout-path = "serial1:115200n8";
	};

	/* Will be filled by the bootloader */
	memory@0 {
		device_type = "memory";
		reg = <0 0 0>;
	};

	aliases {
		emmc2bus = &emmc2bus;
		ethernet0 = &genet;
		pcie0 = &pcie0;
	};

	leds {
		act {
			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
		};

		pwr {
			label = "PWR";
			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
			default-state = "keep";
			linux,default-trigger = "default-on";
		};
	};

	wifi_pwrseq: wifi-pwrseq {
		compatible = "mmc-pwrseq-simple";
		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
	};

	sd_io_1v8_reg: sd_io_1v8_reg {
		compatible = "regulator-gpio";
		regulator-name = "vdd-sd-io";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
		regulator-settling-time-us = <5000>;
		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
		states = <1800000 0x1
			  3300000 0x0>;
		status = "okay";
	};
};

&firmware {
	expgpio: gpio {
		compatible = "raspberrypi,firmware-gpio";
		gpio-controller;
		#gpio-cells = <2>;
		gpio-line-names = "BT_ON",
				  "WL_ON",
				  "PWR_LED_OFF",
				  "GLOBAL_RESET",
				  "VDD_SD_IO_SEL",
				  "CAM_GPIO",
				  "SD_PWR_ON",
				  "SD_OC_N";
		status = "okay";
	};
};

&gpio {
	/*
	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
	 * the official GPU firmware DT blob.
	 *
	 * Legend:
	 * "FOO" = GPIO line named "FOO" on the schematic
	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
	 */
	gpio-line-names = "ID_SDA",
			  "ID_SCL",
			  "SDA1",
			  "SCL1",
			  "GPIO_GCLK",
			  "GPIO5",
			  "GPIO6",
			  "SPI_CE1_N",
			  "SPI_CE0_N",
			  "SPI_MISO",
			  "SPI_MOSI",
			  "SPI_SCLK",
			  "GPIO12",
			  "GPIO13",
			  /* Serial port */
			  "TXD1",
			  "RXD1",
			  "GPIO16",
			  "GPIO17",
			  "GPIO18",
			  "GPIO19",
			  "GPIO20",
			  "GPIO21",
			  "GPIO22",
			  "GPIO23",
			  "GPIO24",
			  "GPIO25",
			  "GPIO26",
			  "GPIO27",
			  "RGMII_MDIO",
			  "RGMIO_MDC",
			  /* Used by BT module */
			  "CTS0",
			  "RTS0",
			  "TXD0",
			  "RXD0",
			  /* Used by Wifi */
			  "SD1_CLK",
			  "SD1_CMD",
			  "SD1_DATA0",
			  "SD1_DATA1",
			  "SD1_DATA2",
			  "SD1_DATA3",
			  /* Shared with SPI flash */
			  "PWM0_MISO",
			  "PWM1_MOSI",
			  "STATUS_LED_G_CLK",
			  "SPIFLASH_CE_N",
			  "SDA0",
			  "SCL0",
			  "RGMII_RXCLK",
			  "RGMII_RXCTL",
			  "RGMII_RXD0",
			  "RGMII_RXD1",
			  "RGMII_RXD2",
			  "RGMII_RXD3",
			  "RGMII_TXCLK",
			  "RGMII_TXCTL",
			  "RGMII_TXD0",
			  "RGMII_TXD1",
			  "RGMII_TXD2",
			  "RGMII_TXD3";
};

&pwm1 {
	pinctrl-names = "default";
	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
	status = "okay";
};

/* SDHCI is used to control the SDIO for wireless */
&sdhci {
	#address-cells = <1>;
	#size-cells = <0>;
	pinctrl-names = "default";
	pinctrl-0 = <&emmc_gpio34>;
	bus-width = <4>;
	non-removable;
	mmc-pwrseq = <&wifi_pwrseq>;
	status = "okay";

	brcmf: wifi@1 {
		reg = <1>;
		compatible = "brcm,bcm4329-fmac";
	};
};

/* EMMC2 is used to drive the SD card */
&emmc2 {
	vqmmc-supply = <&sd_io_1v8_reg>;
	broken-cd;
	status = "okay";
};

&genet {
	phy-handle = <&phy1>;
	phy-mode = "rgmii-rxid";
	status = "okay";
};

&genet_mdio {
	phy1: ethernet-phy@1 {
		/* No PHY interrupt */
		reg = <0x1>;
	};
};

/* uart0 communicates with the BT module */
&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
	uart-has-rtscts;
	status = "okay";

	bluetooth {
		compatible = "brcm,bcm43438-bt";
		max-speed = <2000000>;
		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
	};
};

/* uart1 is mapped to the pin header */
&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_gpio14>;
	status = "okay";
};

&vchiq {
	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
};

// =============================================
// Downstream rpi- changes

#include "bcm270x.dtsi"
#include "bcm271x-rpi-bt.dtsi"

/ {
	soc {
		/delete-node/ pixelvalve@7e807000;
		/delete-node/ hdmi@7e902000;
	};
};

#include "bcm2711-rpi.dtsi"
#include "bcm283x-rpi-csi1-2lane.dtsi"
#include "bcm283x-rpi-i2c0mux_0_44.dtsi"

/ {
	chosen {
		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
	};

	aliases {
		serial0 = &uart1;
		serial1 = &uart0;
		mmc0 = &emmc2;
		mmc1 = &mmcnr;
		mmc2 = &sdhost;
		/delete-property/ i2c2;
		i2c3 = &i2c3;
		i2c4 = &i2c4;
		i2c5 = &i2c5;
		i2c6 = &i2c6;
		/delete-property/ intc;
	};

	vcc: fixedregulator@0 {
		compatible = "regulator-fixed";
		regulator-name = "fixed-supply";
		regulator-min-microvolt = <2500000>;
		regulator-max-microvolt = <2500000>;
		regulator-boot-on;
	};

	osc: oscillator {
		#clock-cells = <0>;
		compatible = "fixed-clock";
		clock-frequency = <25000000>;
		clock-output-names = "mclk";
	};

	/delete-node/ wifi-pwrseq;
};

&mmcnr {
	pinctrl-names = "default";
	pinctrl-0 = <&sdio_pins>;
	bus-width = <4>;
	status = "okay";
};

&uart0 {
	pinctrl-0 = <&uart0_pins &bt_pins>;
	status = "okay";
};

&uart1 {
	pinctrl-0 = <&uart1_pins>;
};

&spi0 {
	pinctrl-names = "default";
	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
	status = "okay";

	ad9832@0{
		#clock-cells = <0>;
		compatible = "ad9832";
		reg = <0>;
		spi-max-frequency = <1000000>;
		spi-cpol;
		//spi-cpha;					  // mode 2 => CPHA = CPOL = 1
		clocks = <&osc>;
		clock-names="mclk";
		vcc-supply = <&vcc>;
	};

	//spidev0: spidev@0{
	//	compatible = "spidev";
	//	reg = <0>;	/* CE0 */
	//	#address-cells = <1>;
	//	#size-cells = <0>;
	//	spi-max-frequency = <125000000>;
	//};

	//spidev1: spidev@1{
	//	compatible = "spidev";
	//	reg = <1>;	/* CE1 */
	//	#address-cells = <1>;
	//	#size-cells = <0>;
	//	spi-max-frequency = <125000000>;
	//};
};

&gpio {
	spi0_pins: spi0_pins {
		brcm,pins = <9 10 11>;
		brcm,function = <BCM2835_FSEL_ALT0>;
	};

	spi0_cs_pins: spi0_cs_pins {
		brcm,pins = <8 7>;
		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
	};

	spi3_pins: spi3_pins {
		brcm,pins = <1 2 3>;
		brcm,function = <BCM2835_FSEL_ALT3>;
	};

	spi3_cs_pins: spi3_cs_pins {
		brcm,pins = <0 24>;
		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
	};

	spi4_pins: spi4_pins {
		brcm,pins = <5 6 7>;
		brcm,function = <BCM2835_FSEL_ALT3>;
	};

	spi4_cs_pins: spi4_cs_pins {
		brcm,pins = <4 25>;
		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
	};

	spi5_pins: spi5_pins {
		brcm,pins = <13 14 15>;
		brcm,function = <BCM2835_FSEL_ALT3>;
	};

	spi5_cs_pins: spi5_cs_pins {
		brcm,pins = <12 26>;
		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
	};

	spi6_pins: spi6_pins {
		brcm,pins = <19 20 21>;
		brcm,function = <BCM2835_FSEL_ALT3>;
	};

	spi6_cs_pins: spi6_cs_pins {
		brcm,pins = <18 27>;
		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
	};

	i2c0_pins: i2c0 {
		brcm,pins = <0 1>;
		brcm,function = <BCM2835_FSEL_ALT0>;
		brcm,pull = <BCM2835_PUD_UP>;
	};

	i2c1_pins: i2c1 {
		brcm,pins = <2 3>;
		brcm,function = <BCM2835_FSEL_ALT0>;
		brcm,pull = <BCM2835_PUD_UP>;
	};

	i2c3_pins: i2c3 {
		brcm,pins = <4 5>;
		brcm,function = <BCM2835_FSEL_ALT5>;
		brcm,pull = <BCM2835_PUD_UP>;
	};

	i2c4_pins: i2c4 {
		brcm,pins = <8 9>;
		brcm,function = <BCM2835_FSEL_ALT5>;
		brcm,pull = <BCM2835_PUD_UP>;
	};

	i2c5_pins: i2c5 {
		brcm,pins = <12 13>;
		brcm,function = <BCM2835_FSEL_ALT5>;
		brcm,pull = <BCM2835_PUD_UP>;
	};

	i2c6_pins: i2c6 {
		brcm,pins = <22 23>;
		brcm,function = <BCM2835_FSEL_ALT5>;
		brcm,pull = <BCM2835_PUD_UP>;
	};

	i2s_pins: i2s {
		brcm,pins = <18 19 20 21>;
		brcm,function = <BCM2835_FSEL_ALT0>;
	};

	sdio_pins: sdio_pins {
		brcm,pins =     <34 35 36 37 38 39>;
		brcm,function = <BCM2835_FSEL_ALT3>; // alt3 = SD1
		brcm,pull =     <0 2 2 2 2 2>;
	};

	bt_pins: bt_pins {
		brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0
				 // to fool pinctrl
		brcm,function = <0>;
		brcm,pull = <2>;
	};

	uart0_pins: uart0_pins {
		brcm,pins = <32 33>;
		brcm,function = <BCM2835_FSEL_ALT3>;
		brcm,pull = <0 2>;
	};

	uart1_pins: uart1_pins {
		brcm,pins;
		brcm,function;
		brcm,pull;
	};

	uart2_pins: uart2_pins {
		brcm,pins = <0 1>;
		brcm,function = <BCM2835_FSEL_ALT4>;
		brcm,pull = <0 2>;
	};

	uart3_pins: uart3_pins {
		brcm,pins = <4 5>;
		brcm,function = <BCM2835_FSEL_ALT4>;
		brcm,pull = <0 2>;
	};

	uart4_pins: uart4_pins {
		brcm,pins = <8 9>;
		brcm,function = <BCM2835_FSEL_ALT4>;
		brcm,pull = <0 2>;
	};

	uart5_pins: uart5_pins {
		brcm,pins = <12 13>;
		brcm,function = <BCM2835_FSEL_ALT4>;
		brcm,pull = <0 2>;
	};
};

&i2c0if {
	clock-frequency = <100000>;
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;
	clock-frequency = <100000>;
};

&i2s {
	pinctrl-names = "default";
	pinctrl-0 = <&i2s_pins>;
};

/ {
	__overrides__ {
		/delete-property/ i2c2_baudrate;
		/delete-property/ i2c2_iknowwhatimdoing;
	};
};

&firmwarekms {
	compatible = "raspberrypi,rpi-firmware-kms-2711";
};

// =============================================
// Board specific stuff here

/ {
	sd_vcc_reg: sd_vcc_reg {
		compatible = "regulator-fixed";
		regulator-name = "vcc-sd";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		enable-active-high;
		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
	};
};

&sdhost {
	status = "disabled";
};

&emmc2 {
	vmmc-supply = <&sd_vcc_reg>;
};

&phy1 {
	led-modes = <0x00 0x08>; /* link/activity link */
};

&gpio {
	audio_pins: audio_pins {
		brcm,pins = <40 41>;
		brcm,function = <4>;
	};
};

&leds {
	act_led: act {
		label = "led0";
		linux,default-trigger = "mmc0";
		gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
	};

	pwr_led: pwr {
		label = "led1";
		linux,default-trigger = "default-on";
		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
	};
};

&pwm1 {
	status = "disabled";
};

&audio {
	pinctrl-names = "default";
	pinctrl-0 = <&audio_pins>;
};

&vc4 {
	status = "disabled";
};

&pixelvalve0 {
	status = "disabled";
};

&pixelvalve1 {
	status = "disabled";
};

&pixelvalve2 {
	status = "disabled";
};

&pixelvalve3 {
	status = "disabled";
};

&pixelvalve4 {
	status = "disabled";
};

&hdmi0 {
	status = "disabled";
};

&ddc0 {
	status = "disabled";
};

&hdmi1 {
	status = "disabled";
};

&ddc1 {
	status = "disabled";
};

/ {
	__overrides__ {
		act_led_gpio = <&act_led>,"gpios:4";
		act_led_activelow = <&act_led>,"gpios:8";
		act_led_trigger = <&act_led>,"linux,default-trigger";

		pwr_led_gpio = <&pwr_led>,"gpios:4";
		pwr_led_activelow = <&pwr_led>,"gpios:8";
		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";

		eth_led0 = <&phy1>,"led-modes:0";
		eth_led1 = <&phy1>,"led-modes:4";

		sd_poll_once = <&emmc2>, "non-removable?";
		spi_dma4 = <&spi0>, "dmas:0=", <&dma40>,
			   <&spi0>, "dmas:8=", <&dma40>;
	};
};